Asko D5644 Bedienungsanleitung PDF herunterladen (Seite 15)

FORMAT A4

This document must not be copied without

our written pemission, and the contents

thereof must not be imparted to a third party

nor be used for any unauthorized purpose.

Contravention will be prosecuted.

Asko Appliances AB

CIRCUIT DIAGRAM DW90.1, DW90.1OEM, DW90.2, DW90.C, DW90.3

80 840 68-01

Displays

DW90.1

Panel type DW90.1, L = LED, T = Push-button

DW90.1 OEM

Panel type DW90.1 OEM, L = LED, T = Push-button

DW90.2

Panel type DW90.2, L = LED, T = Push-button

DW90.3

Panel type DW90.3, T = Touch areas

L10

L11

PROGRAM

Graph.

Area

T6T7T5

L12

T11

T10

Failure

F:XX Last failure read out. F10 Overfillig, F11 Drain,

F12 Water inlet,F40 Valve leakage, F41 Temp.

stop,F42 Thermistor, F43 Pressure sensor,

F44 Turbidity sensor, F45 Diverter

START (T2)

Diagnostic

d:01 Mix valve and inlet valve on (1 sec delay

between mixventil and inlet valve)

d:02 Inlet valve on

d:03 Salt Valve on

d:04 Combi dispenser on

PROG (T1) d:05 Circulation and spolarmsväxlaren (if available)

shall alternate between positions 1 and 3 every

30 seconds

d:06 Circulation and heaters - max 75 ° C

d:07 Fan and vax actuatoor

d:08 Drain Pump on

d:00 No components on

START (T2)

Water inlet

P:0 Normal water intake, default

P:5 Water intake increased +5%

P:10 Water intake increased +10%

PROG (T1) P:15 Water intake increased +15%

L:0 Time, flow meter disconnected, inlet time: no of

pulses x 0.068 [s]

L:5 Timed water intake increased +5%

L:10 Timed water intake increased +10%

L:15 Timed water intake increased +15%

START (T2)

Variant,

DW90.1

U:1 DW90.1

U:2 DW90.1 OEM

Variant 1 and 2, the default setting

(temperature, drying)

U:3 DW90.1

U:4 DW90.1 OEM

Variant 3 and 4 (Temperature, Drying, Delayed

Start)

PROG (T1) U:5 DW90.1

U:6 DW90.1 OEM

Variant 5 and 6 (Set of time program,

Temperature, Drying, Time saving, Delayed

Start)

U:7 DW90.1 and

DW90.1OEM

Variant 7 (Set of time program, Temperature,

Drying, Time-saving, Upper Lower basket wash,

Delayed Start)

Variant,

DW90.2

U:1 Variant 1, the default setting (temperature,

drying)

U:2 Variant 2 (Temperature, Drying, Delayed Start)

PROG (T1) U:3 Variant 3 (Temperature, Drying, Delayed Start,

Set of time program)

U:4 Variant 4 (Temperature, Drying, Delayed Start,

Set of time program, Time saving)

START (T2)

Region

EU Region Europe, the default setting

PROG (T1) US Region USA

AU Region Australia

START (T2)

Fan

Sequence

Y:0 No fan sequence during wash cycle

PROG (T1) Y:1 Fan sequence during the wash cycle but not in

Normal program, the default setting

Y:2 Fan in sequence during the all wash cycles

START (T1)

TDE & HWC,

only DW90.2

A:0 Turbo Drying Express and Heat Water Circuit

off, default setting

PROG (T1) A:1 Turbo Drying Express on

A:2 Heat Water Circuit on

START (T2)

ECO, only

DW90.1

E:0 ECO off, the default setting

PROG (T1) E:1 ECO on, when the machine is connected to

hot water consumed less electrical energy to

heat water and program time is shortened.

START (T2)

Super rinse

S:0 Super Rinse, default

PROG (T1) S:1 Super Rinse on. Adding two extra rinses.

START (T2)

Total restart

r:0 No restart on the next press T2, default

PROG (T1) r:1 Total restart at the next press T2

START (T2)

DW90.1, DW90.1 OEM, DW90.2

After power on, wait until LCD is turned on. Then, within 5sec, press first T1 and

directly after T2. Hold both buttons pressed during 5sec to enter service menu.

START (T2)

Failure

CU Date code xxxx Control unit manufacturing date:year week

Software xxx Software version

PROG (T1) 3 FAIL. xxxx Last failure

2 FAIL. xxxx 2nd last failure

1 FAIL. xxxx 3rd last failure

START (T2)

Diagnostic

Testing No component on

Testing Valve A: XXX Mix valve on and inlet valve on (1 sec delay

between mix valve and inlet valve), flow in

pulses(XXX) by flow meter

Testing Valve B: XXX Inlet valve on (1 sec delay), flow in pulses(XXX)

by flow meter

PROG (T1) Testing Salt Salt valve on

Testing Dispenser Kombi dispenser on

Testing Cirk: XXV Circulation pump on and the water diverter

valve(if present) shall change between position

1 and 3 every 30 second, turbidity(XX) in Volt

Testing Heater: XX°C Circulation pump and heater on until max 75°C,

temp displayed in °C or °F according to

machine setup

Testing Fan: XXXX Fan and wax actuator on, humidity value(XXXX

Hz)

Testing TDE TDE fan on and TDE heater on

Testaing Drain: XXV drain pump on , pressure sensor value(XX) in

Volt

START (T2)

Water inlet

Water volume 0 Normal water intake, default

Water volume +5% Water intake increased +5%

Water volume +10% Water intake increased +10%

Water volume +15% Water intake increased +15%

PROG (T1) Water volume Time 0 Time, flow meter disconnected, inlet time: no of

pulses x 0.068 [s]

Water volume Time +5% Timed water intake increased +5%

Water volume Time +10% Timed water intake increased +10%

Water volume Time +15% Timed water intake increased +15%

START (T2)

LCD-cont

Contrast 0 LCD-contrast 0

Contrast +1 LCD contrast +1

PROG (T1) Contrast +2 LCD contrast +2

Contrast -1 LCD contrast -1

START (T2)

TDE

Turbo Drying On Turbo Drying Express On

PROG (T1) Turbo Drying Off Turbo Drying Express off

START (T2)

Fan seq.

Fan Off No fan sequence during wash cycle

PROG (T1) Fan 1 On Fan sequence during the wash cycle but not

in Normal program, the default setting

Fan 2 On Fan in sequence during the all wash cycles

START (T2)

DUO

DUO Off DUO Off

PROG (T1) DUO On DUO On, to activate frogram like Sani, Pots

& pans

START (T2)

Region

Region EU Region Europa, default setting

Region US Region USA

PROG (T1) Region AU Region Australien

START (T2)

DW90.3

To enter service menu, press T1 and T2 at power on.

T5 T1

1 2 ... 10 11 12 13 14 15

Kommentare zu diesen Handbüchern

Keine Kommentare

Asko D5644 Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Asko D5644